Why interlocking stone sinks and heaves in Ottawa
By Rinku Singh
Published October 23, 2026
Interlocking stone sinks when the base is too shallow or not compacted properly. It heaves when water gets into the base and freezes. Ottawa’s clay soil, freeze-thaw cycles, and wet springs make both problems common. The fix is a deep, well-drained granular base, proper compaction, and edge restraint to prevent spreading.
Why does interlock sink in Ottawa?
Sinking happens when the base material compresses under load. That load can be vehicle weight, foot traffic, or just the freeze-thaw cycle compressing inadequately compacted material over time.
The three most common causes are:
-
Base too shallow. A patio that only carries foot traffic needs 6 to 8 inches of compacted granular base. A driveway needs 10 to 12 inches. If the installer skimps and uses 4 inches, the base compresses under load and the pavers settle. Low spots collect water, which makes the problem worse.
-
Base not compacted properly. Granular base must be compacted in lifts (layers), typically 3 to 4 inches per lift, with a plate tamper or jumping jack. If the installer dumps 10 inches of gravel and compacts only the top, the bottom stays loose and settles over time.
-
Interlock installed over clay without base. Clay expands when wet and shrinks when dry. If pavers are laid directly on clay or on a thin sand layer over clay, they move with the clay. The first freeze-thaw cycle or heavy rain shifts the pavers and creates an uneven surface.
The fix for sinking is to lift the pavers, add more base material, compact it properly in lifts, and relay the pavers. Trying to shim sunken pavers with sand does not work; the sand washes out and the pavers settle again.
Why does interlock heave in Ottawa?
Heaving happens when water in the base freezes and expands. Ice takes up about 9 percent more volume than water, so when the base is saturated and freezes, it pushes the pavers up. When it thaws in spring, the base settles but not always evenly, leaving the surface wavy or uneven.
Ottawa’s freeze-thaw cycles are brutal. The temperature crosses zero dozens of times each winter, which means the base freezes and thaws repeatedly. Each cycle pushes water deeper into the base if drainage is poor.
The three most common causes of heaving are:
-
Clay base that holds water. Clay is impermeable; water sits in it instead of draining through. If the granular base sits directly on clay without a drainage path, the base stays saturated all winter and heaves when frozen.
-
No edge restraint. Pavers without edge restraint (plastic spikes or concrete curbing) spread over time. Gaps form at the edges, water gets in, and the base saturates. The frozen base pushes the pavers up in winter and the whole surface becomes uneven.
-
Poor surface drainage. If the interlock does not slope away from the house or structure, water pools on the surface, percolates into the joints, and saturates the base. In winter that water freezes and heaves the pavers.
The fix for heaving is to ensure the base is granular material that drains (clear stone, crusher run, or 3/4” limestone), slope the surface for drainage, and install proper edge restraint. If the base is already saturated and heaving, the pavers must be lifted, the base must be replaced with free-draining material, and the surface must be regraded for proper runoff.
What is the right base for Ottawa interlock?
The base must be granular material that drains, deep enough for the load, and compacted in lifts. The standard base for Ottawa interlock is:
- Patio or walkway: 6 to 8 inches (150 to 200 mm) of compacted 3/4” clear stone or crusher run.
- Driveway: 10 to 12 inches (250 to 300 mm) of compacted 3/4” clear stone or crusher run.
- Steps or retaining walls: 12 to 18 inches (300 to 450 mm) depending on wall height and load.
The base sits on undisturbed subgrade or compacted granular fill, not on clay or topsoil. If the excavation exposes clay (common in Ottawa), the clay is left undisturbed or, if it was disturbed, replaced with granular fill and compacted.
On top of the base goes a 1-inch (25 mm) layer of bedding sand (concrete sand or mason sand, not beach sand or topsoil). The sand is screeded level and the pavers are laid on it. After the pavers are laid, polymeric sand is swept into the joints. Polymeric sand hardens when wet and prevents the joints from washing out.
Edge restraint (plastic paver spikes or poured concrete curbing) is installed along all edges to prevent the pavers from spreading. Without edge restraint, the pavers migrate outward over time, gaps form, and the base fails.
How do I know if my base is failing?
The warning signs are:
- Low spots or waves in the surface. If you can see dips or humps when you stand back and look across the surface, the base has settled unevenly.
- Gaps between pavers that were not there when the interlock was new. This means the pavers are spreading or the base is compressing.
- Pavers rocking or shifting when you walk on them. This means the base is loose or the sand layer has washed out.
- Pooling water after rain. This means the surface is no longer draining properly, often because the base has settled and the slope has reversed.
- Weeds or moss growing in the joints. This means the polymeric sand has washed out or was never installed, and organic material is filling the joints. Water follows and saturates the base.
If you see these signs, the base is failing. Small areas can sometimes be repaired by lifting pavers, adding base material, and relaying. Large areas or areas with significant heaving usually need full excavation, new base, and reinstallation.
Can I repair settled or heaved interlock myself?
Small areas, maybe. If a 2x2 foot section has settled and you want to lift it, add sand, and relay the pavers, you can try. But if the problem is a shallow or poorly compacted base, adding sand will not fix it; the pavers will settle again within a year.
Large areas, no. If the driveway has multiple low spots or the patio is heaving along one side, the problem is the base, not the pavers. Fixing it requires lifting all the pavers, excavating the base, adding proper granular material, compacting it in lifts, and relaying the pavers with new bedding sand and polymeric sand. That is a full reinstall and requires equipment (a skid-steer, plate tamper, and usually a dump truck for disposal).
DIY repairs also miss the drainage issue. If the base failed because water is not draining, lifting pavers and adding sand does not fix the drainage. The base will saturate again and the problem will recur.
What does a proper interlock installation look like?
A proper Ottawa interlock job includes:
-
Excavation to proper depth: 6 to 8 inches for patios, 10 to 12 inches for driveways, deeper for steps or walls. The subgrade is compacted or left undisturbed (never loose).
-
Granular base in lifts: Clear stone, crusher run, or 3/4” limestone spread in 3- to 4-inch lifts and compacted with a plate tamper or jumping jack after each lift. The base is level or sloped for drainage (minimum 2 percent slope away from structures).
-
Bedding sand: 1 inch of concrete sand or mason sand screeded level over the compacted base. The pavers are laid on the sand, not on the base material.
-
Edge restraint: Plastic paver spikes every 12 inches along all edges, or poured concrete curbing, to prevent the pavers from spreading.
-
Polymeric sand in joints: Swept into the joints, misted with water to activate, and left to cure. This prevents the joints from washing out and stops weeds from growing.
-
Proper drainage: The surface slopes away from the house or structure at a minimum 2 percent grade (2 cm per metre, or 1/4 inch per foot). Water runs off the surface and does not pool.
That process takes longer and costs more than dumping gravel, laying pavers, and calling it done. But it is the only way interlock lasts in Ottawa’s climate.
What should you expect from us?
We excavate to proper depth, compact the base in lifts, and install edge restraint on every Ottawa interlock job, because shortcuts mean callbacks when the pavers settle or heave.
The quote specifies base depth, material type, and compaction method so you know what you are getting. We do not install interlock over clay without a proper granular base, and we do not compact 10 inches of base in one pass. The work takes longer but the result lasts.
If we are repairing existing interlock that has failed, we assess whether the base can be salvaged or whether full excavation and reinstall is required. Small settled areas can sometimes be lifted, based, and relaid; large heaved areas or areas with inadequate base usually require full reinstall.
Typical payment terms are a deposit at signing, a progress payment after excavation and base are complete, and final payment after pavers are laid and joints are swept.
Ready to install or repair interlock? Read the full interlock service page or request a quote and we will visit your Ottawa property to assess the site, discuss your priorities, and explain what the base and drainage plan will be.